Skip to main content

Solenoid Control Valves

Hydraulic Control Valves

The Solenoid Controled Valve is the hydraulic control valve operated by line pressure and designed to ensure opening/closing process by means of built-in 3/2-way solenoid pilot valves controlled remotely with electric signal. Electric signal for solenoid pilot valves is ensured by means of a control device, time relay, main switch and PLC control units etc. Opening/Closing process may be realized easily thanks to manual control on solenoid pilot valve. Depending on desire, 24V AC 50Hz/60Hz or 12V DC, 9V DCLATCH and 12V DC latch normally open (N.O.) or normally closed (N.C.) solenoid coils may be used on main valve.

Coil Options

  • Baccara 24 V AC
  • Baccara 12 V DC Latch
  • Burkert 24 V AC

Existing Diameters According To Their Connections

  • Flanged: DN50, … , DN300
  • Angled: 2″, DN50, DN80, DN100, DN150
  • Threaded : 3/4″, 1″, 1¼”, 1½”, 2″, 2½”, 3″
  • Victaulic : 2″, 3″, 4″, 6″
Solenoid Control Valves - Catalog
Operating Pressure
 Standart 0,7 – 16 bar (10 – 240 psi)
Low Pressure Range 0,5 – 10 bar (7,5 – 160 psi)
High Pressure Range 0,7 – 25 bar (10 – 360 psi)
Temperature
 Min. Operating Temperature -10 °C (14 °F) DIN 2401/2
Max. Operating Temperature 80 °C (176 °F) DIN 2401/2
Port
 Flanged DIN 2501, ISO 7005 – 2
Threaded ISO (BSP) , ANSI (NPT)
Coating
 Standard Epoxy
Optional Polyester
Hydraulic Links
 Standard Reinforced Nylon (Air Brake))
Hydraulic pipe SAE J 844
Optional Copper DIN 1057
Actuator Type
 Single-Control Housing | Aperture Actuator, Aperture Off

Automatic control valves are used to perform the required operations as hydraulic with line pressure without the need for energy sources in the network line.

Valve Closing Mode

When the water pressure reaches the diaphragm, the water creates hydraulic force. This hydraulic force diaphragm, combined with the force applied by the spring creates a complete seal and allows it to close.

Valve Opening Mode

When the pilot on the main control valve in the closed position is placed in the evacuation position, pressurized water on the diaphragm of the main control valve is discharged. When the line pressure reaches the position to overcome the spring force, it applies hydraulic force from the bottom to the diaphragm of the control valve and allows the valve to reach the full open position

Modulation Mode

They are pilots connected to the control valve which enables the main valve to operate in this position. According to the amount of flow and pressure required to be adjusted, it controls the water pressure on the diaphragm continuously and allows it to operate in modulated position.

  • Easy operation and maintenance with simple structure
  • Low cost
  • Working at wide pressure value range
  • Perfect modulation even at low flow rates
  • Continuous on / off with flexible aperture
  • Full seal with reinforced diaphragm and inner spring
  • Long life with epoxy-polyester coating
  • Wide range of control area with the use of different pilot valves
  • Ability to work in horizontal and vertical positions in application areas
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
Valve Diameter
 2 50 2½ 65 3 80 4 100 5 125 6 150 8 200 10 250 12 300
CV m³/h @ 1 bar
 88 88 174 187 187 419 1139 1698 2276
Kv gpm @ 1 bar
 102 102 201 216 216 484 1316 1961 2629

KV: Valve flow Coefficient (Flow Rate At 1 Bar Pressure Loss M³/h @ 1 BAR)

CV: Valve flow Coefficient (Flow in pressure lossof 1 Psi GPM @ 1 Psi)

Q: Flow (M³/h, GPM)

ΔP: Pressure Loss (BAR, PSİ)

G: Specific Gravity of Water (For water = 1.0)

Installation
  • After connecting to Valve Inlet, finger filter number 3 and mini ball valve number 2, connection to solenoid pilot’s “I” outlet and 3-way valve’s “C” outlet is provided with copper or plastic pipe.
  • Solenoid pilot’s “II” number is connected to the auto “A” output of 3-way valve.
  • Valve outlet” 4 ” is connected to the blind.
  • Valve rated diameter should be the same or a small rated diameter as the line diameter.
  • In the direction of the arrow indicated on the valve Mount.
  • Isolation valves (butterfly or sliding valve etc.) in the line Assembly of the valve.B) it is recommended to use air discharge valve, quick pressure discharge control valve (QR) and dirt retaining valves.
  • Cavitation risk during pressure drop is dangerous for valve body. Adjust the output pressure value you want to adjust by looking at the cavitation chart or contact our company.
Adjusting
  • Connect the solenoid pilot valve wiring indicated by “5” to the control device.
  • Turn on the pump or turn on the mains main valve and give water to the system.
  • Open ” 2 ” spherical valve at Valve entrance
  • Then turn the three-way selector valve indicated by “1” on the valve to “auto” position.

 

  1. Three-Way Mini Ball Valve
  2. Mini Ball Valve
  3. Finger Filter
  4. Blind plug
  5. Solenoid Pilot

FLANGED
Available Diameters
 mm 50 65 80 100 125 150 200 250
inch 2 2½ 3 4 5 6 8 10
Port
 Flanged
Material
 GG25 – GGG40
Body
 Globe
Transmission Pressure
 PN10 – PN16 – PN25

VICTAULIC
Available Diameters
 mm 50 65 80 100 150
inch 2 2½ 3 4 6

 
Port
 Victaulic
Material
 GG25 – GGG40
Body
 Globe
Transmission Pressure
 PN10 – PN16 – PN25

THREADED
Available Diameters
 mm 25 40 50 65 80×50 80
inch 1 1½ 2 2½ 3x2x3
Port
 Threaded
Material
 GG25 – GGG40
Body
 Globe
Transmission Pressure
 PN10 – PN16 – PN25

ANGELED
Available Diameters
 mm 50 80 100 150
inch 2 3 4 6
Port
 Flange – Threaded
Material
 GG25 – GGG40
Body
 Globe
Transmission Pressure
 PN10 – PN16 – PN25